Ure Museum Database



Browse
There are 26 objects for which Shape_description contains → hollow
14.9.115 Top half of hollow figurine in the shape of a youth 2002.97.0411.jpg
2016.5.2 Open rim separated from the body by a grooved band. Shallow body. Slightly oblique handles of the stick type. Conical hollow foot with flexed walls.
25.4.2 Four-handled. Kylix style, stemmed and hollow inside stem. Handles round. At halfway points between handles are two more sets of handles but these have broken off. 2003.58.0009.jpg
25.9.1 Base is hollow although filled with modern plaster. 2003.23.0003.jpg
26.12.7 Stemmed. The vessel is slanted to one side, which suggests that the base is not flat or that the body has not been made to rest flat on top of the foot. The wide rim has a flat lip. The base hollow to where the bottom of the bowl rests. 2003.58.0008.jpg
27.4.12 Very shallow bowl. Foot hollow. 2002.97.0239.jpg
29.11.12 Pig. Hollow, with a small (vent) hole underneath 2002.97.0749.jpg
33.4.1 Four-handled. Stemmed. Kylix style. Foot and stem hollow. 2003.58.0011.jpg
34.10.22 Nude standing youth holding cock in left hand. Inside is completely hollow. 2002.97.0377.jpg
34.10.26 Fragment of head and neck of large figuring (female). Inside is completely hollow. 2002.97.0426.jpg
34.10.27 Standing male figure in a cloak with his legs crossed, leaning on a support to his right. Figurine is hollow and has large hole in the back. No relief sculpture on the reverse side. 2005.89.0041.jpg
45.6.66 Circular deep body with small lip leading to a large filling hole. At the centre of the reservoir is a central circular hollow which is no taller then the rim of the lamp and widens towards the base of the lamp. The nozzle is flat but at a slight incline, the tip of the nozzle is irregular, one side is rounded, the other is angular, the wick hole is oval. Base is a slightly concave ring with parallel circumferences. 2005.01.0072.jpg
51.4.11 Moulded rim, grooved, with flat upper surface and sharp lip, on a short cylindrical neck, with attaches, at a ridge, to an ovoid body, attached below, also at a ridge, to a slightly flaring stand, with splaying foot, slightly ridged on upper edge, bevelled on exterior, hollow on the interior. From the shoulder, on either side, rises an m-shaped handle (half of one chipped off) with short projections in the middle. Three holes (to enable air flow) are drilled into the upper part of the stand, just below the join. 2002.97.0369.jpg
56.8.6 Rounded cup with sharply incurving rim and shallow bowl, on a short hollow stem which broadens to a disk foot with a grooved foot, and deeply concave underside. 2010.98.0102.jpg
57.3.11 Fragment of a female head from large figurine, hollow inside. 2003.98.0069.jpg
67.6.3 Hollow, large opening in back and hole in base. Back of figurine is left unformed. 2004.95.0067.jpg
L.2005.8.1 Disks with spindles through the middle (one hollow)
L.2011.1.13 Central circular knob, with a round tip and a sort of carination in the edge, hollow in the underneath; rounded rim, hollow inside, connected to the knob by a quite sloping lid. 2011.97.0183.jpg
L.2011.1.47 Knob and the upper part of the lid. No stem, ridge in the upper part of the knob, flat tip. Hollow in the underneath. 2011.96.0074.jpg
L.2016.3.32 Small, relatively heavy metal horn; hollow inside. Moulded bulges line up along the curved body, probably to sketch the natural form, and lead to the rounded tip. Four holes surround the upper part of the horn (actually the end attached to the head). The horn ends with a flat rim.
REDMG:1934.53.4 Broad flaring lip, convex on the upper surface, with a downturned rim, offset from a concave shallow bowl; hollow high stem offset from plate but spreading at the bottom into a disk foot, hollowed on the interior. 2004.99.0437.jpg
REDMG:1935.87.2 Two tall handles, which each extend from the neck to the top of the shoulderr; resting surface slopes slightly; base hollow. 2002.97.0713.jpg
REDMG:1935.87.6 Rounded rim on tapered flange, below which the walls spread out to a thin element that would have supported the lid; just below this are attached two horizontal horseshoe-shaped strap handles, slightly canted upwards, to which spurs are attached on either side. The lower body is offset from the handle zone, rounded in the lower part where it sharply joins a moulded foot, with groove above a spreading upper part and a broader, rounded lower part, hollow on the interior, with a narrow resting surface, and a pointed, slightly offset underside.
REDMG:1953.25.32 Kalathos-shaped body, with a flaring rounded rim, to the top of which are attached the looped ends of a pair of strap handles, concave on their exterior surfaces; the tubular ends of the loops rejoin the middle of each handle, and below the bottom of each handle, attached at the bottom of the cup, is a spur. Below a carination, the bottom of the cup narrows to a nearly cylindrical stem, ridged at the center, below which it widens, and smoothly curves into the top of a moulded foot, with three ridges, of increasing diameter, on the exterior surface. Within the narrow resting surface is a concave underside, with a conical hollow at centre. 2005.89.0006.jpg
REDMG:1953.25.40 Rounded rim on tapered flange, below which the walls spread out to a thin element that would have supported the lid; just below this are attached two horizontal horseshoe-shaped strap handles, slightly canted upwards. The body is rounded in the lower part and sharply joins a moulded foot, with an angled upper part and a broader, rounded lower part, hollow on the interior, with a narrow resting surface. 2003.97.0324.jpg
REDMG:1964.1154.1 Outturned rounded rim , narrowing to a nearly cylindrical body (broadens slightly below) that narrows sharply to a short, nearly cylindrical stem, attached to a pedestal foot, hollow within, slightly angled on the upper surface, nearly vertical on the sides, flaring to a slighted everted base, with a rounded resting surface 2004.99.0831.jpg
The Ure Museum is part of
The University of Reading, Whiteknights, PO Box 217, Reading, RG6 6AH